How to make a simple one piece silicone mould | Lure Anglers Forum - Lure Fishing Forum UK (Bass, wrasse..)
Forum Supporting Contributions Upgrade Here

How to make a simple one piece silicone mould

Discussion in 'DIY & Home Made Lures' started by {name}, May 5, 2012.

  1. Perch

    432
    362
    63
    Location:
    Southampton
    Hi,

    As promised here is my next instalment on how I make my soft plastic lures and probably the most important part in the whole process. Mould making is really easy once you get used to doing it but it is really important to take your time and get it right, as it can sometimes be difficult to correct mistakes. The key thing to think about when doing this is, the better the mould the better the end result will be.

    There are a few different materials that you can use for making you moulds but by far the easiest to use is RTV or room temperature vulcanising Silicone. This material usually comes in a two part kit consisting of a white silicone base and a catalyst, which is usually coloured to make it easy to see that you have mixed it correctly. The advantage of using silicone is that it fully cures within 24 hours and is ready to use straight away and can also withstand heat from the plastic. It will make a perfect impression of whatever you pour it over, which can have disadvantages when there are slight imperfections.

    STEP 1: Choosing a container...

    The first step of the process is to find or make a suitable container to make your mould in. You will need something reasonably strong that will not leak and has a flat bottom. In the past I have tried various containers quite successfully, including tupperware boxes, used food containers and even wood. The problem I have found with most plastic containers is that they do not have a totally plain flat bottom so this can restrict how large your lure can be. Also they have quite a large capacity so you will end up using much more RTV silicone than is necessary. Do not use anything made of glass or pyrex, although it looks like it will give a good finish the silicone will stick to it and will be very hard to remove.

    Another method I have found is to make a simple mould box from foam core board. This is now my preferred method and is what I am going to show you here. Foam core board basically a piece of stiff foam which is about 6mm thick and has almost glossy paper on both sides. It is usually sold in craft shops next to where they keep sheets of coloured cardboard and paper. It is also reasonably inexpensive at £3.99 for an A1 sheet from hobbycraft or the Range.

    So the items you will need to make the box are as follows:

    1. a sheet of 6mm foam core board
    2. a hot glue gun
    3. Aluminium foil tape or any strong tape
    4. a steel ruler (safer to use than plastic when cutting)
    5. a marker pen
    6. a Stanley or craft knife
    7. some T pins (used for model making and can be found quite cheap on ebay)
    8. some double sided foam mounting tape.


    [​IMG]


    The first step is to decide what size the base of your mould will be. As you can see in the photo I have drawn a box on the foam board, around a wooden master that I want to make the mould from. It is important to make allow about 15 - 20 mm around the master as this will ensure that the silicone will hold its shape, any less and you risk the cavity collapsing slightly and an unusable mould. The base I have marked out here is 40mm x 170mm.


    [​IMG]


    Next we need to draw out the sides on the mould box. First thing to do here is measure the lure to the highest point which was about 15mm and add another 15 - 20mm, this gives me the depth of the box. As you can see in the picture I have marked out a long strip with one piece at 46mm then 170mm, 40mm and 170mm all at 35mm high. One of the short sides needs to be 6mm longer to allow for overlap when it is formed around the base.


    [​IMG]


    Next using the steel ruler and Stanley knife carefully cut out the marked parts of the mould box.


    [​IMG]


    Then on the long strip that makes the sides carefully cut along the lines of the corners, but not all the way through leaving one side of the paper intact. When the corners are folded the foam will crack and will leave a hinged corner. This piece can now be folded around the base.


    [​IMG]


    The open end of can be fixed into place by using two T pins pushed through into the foam of the joining end.


    [​IMG]


    Already you will notice how solid this box feels but to reinforce it and stop any leaks, all edges must be covered in tape. I guess you could use gaffer or something like that but the foil tape I have used gave a strong finish and was very adhesive. After this is done it is a good idea to seal the inside edges using the hot glue gun, silicone can get into the tiniest of gaps so this will keep your finished mould quite neat.


    [​IMG]


    Next step is fixing the master into the base of the box. I have used double sided foam mounting tape as it deals with any imperfections on the bottom of the master and gives a good seal to stop the silicone seeping underneath it in the mould box.


    [​IMG]


    When it is stuck onto the master I carefully trimmed the excess, removed the backing tape and stuck it onto the centre of the base.

    The mould box is complete...


    [​IMG]


    STEP 2: Mixing and pouring the silicone


    The next step is to prepare and pour your RTV Silicone into the mould box.


    [​IMG]


    A 1.1kg kit as shown here will make about 5 or 6 single moulds or one large multi cavity mould. To avoid wastage and get the most out of the kit you first need to work out the volume of the mould. The easiest way I found to do this was to use something dry like rice and I filled the mould with it.


    [​IMG]


    The rice can then be poured into a measuring jug to work out the volume. Here you can see it is around 150ml.


    [​IMG]


    For mixing the silicone I use a plastic measuring jug, as any that is left in the jug can be easily peeled off when cured and the jug can be reused. As I have mentioned before if you use glass then the silicone can stick to it and is almost impossible to remove.

    The mixing ratio for this silicone is 10% catalyst to silicone base, either by weight or volume. So I poured 150ml of the silicone base into a plastic jug and added 15ml of catalyst using a measuring syringe.


    [​IMG]


    Then thoroughly mix the two parts together in the jug, making sure that the sides and bottom are scraped and no white base material can be seen through the jug. Try not to do this too vigorously as you don't want to add too much air and bubbles into the silicone. Mixing can take a few minutes and it is important to make sure it is fully mixed as the silicone may not fully cure if not done right. When done you will start to see the catalyst working as tiny bubbles will form and rise to the top. It may be a good idea to leave the silicone to rest for about 10 minutes just to let the first bubbles come out of the silicone as most form when first mixed.


    [​IMG]


    Now it is time to pour the silicone into the box. As mentioned before bubbles will form in the silicone and if these end up in the cavity of the mould then they will be noticeable on your cast lure. There are a couple of methods to ensure this does not happen, one of which is to paint a very thin coat of silicone over the master and make sure there are no bubbles in that coat before pouring the rest of the silicone. The only problem with this method is that once you have put silicone on a paint brush it is hard to remove and will need to be binned.

    The method I use is to slowly pour a very small stream of silicone from height into one corner of the mould box. The small stream will break most of the bubbles as it goes in and as the silicone moves over the master air is slowly pushed out and none is trapped in the detail. This has worked perfectly almost every time for me, as long as it is not rushed.
    Here you can see the silicone is slowly pouring into one corner...


    [​IMG]


    Keep pouring on the same spot until the master is fully covered...


    [​IMG]


    Here are some fully poured moulds...


    [​IMG]


    Once the silicone is fully poured, gently tap the mould box on a hard surface just to make sure there are definitely no bubbles formed on master. This will make the bubbles rise up and pop at the surface and you will see this happening for a while until silicone begins to set. You can also spray a thin coat of wd40 to break the surface tension and allow the bubbles to pop quicker. It is important as the name says to let the silicone cure at room temperature and also on a level surface, total curing will take about 24 hours. If the silicone is left to cure at colder temperatures, then the cure time will be much longer.

    After 12 - 24 hours, check that the silicone is hard and then remove the boxes from around the mould. This can be easily done with the foam board as it can be cut or broken off. The master may stay within the silicone but can be pulled out quite easily. You may find that there is little leakage under the masters but this can be easily trimmed back with a pair of scissors.

    Here are the moulds ready for use...


    [​IMG]


    Coming up next is how to pour your soft plastic lures...

    :)
     
    Last edited: Jul 17, 2012
    • Like Like x 40
  2. Striper

    3,604
    1,754
    113
    Location:
    Guernsey
    Nice one Alan, much neater than my chuck it all in a plastic box method.
     
  3. Perch

    432
    362
    63
    Location:
    Southampton
    Thanks Andy! I think it was more tiring writing up the thread than actually making the moulds... :)
     
  4. Striper

    3,604
    1,754
    113
    Location:
    Guernsey
    I can agree with that, it takes ages doing the step by step. Theres some I did a while back on mould making and pourig etc on here somewhere.
     
  5. Pollock

    1,540
    922
    113
    Location:
    West Sussex
    Excellent stuff Alan, roll on the lurefactors :)
     
  6. Perch

    364
    53
    28
    Location:
    conwy
    Nice one alan very informative:clap:
     
  7. Striper

    2,192
    1,498
    113
    Location:
    Buckinghamshire
    Very good article Alan. I love it :)
     
  8. Blanker

    2
    1
    0
    Location:
    Guernsey
    Nice one must be cool catching on something you made yourself
     
  9. Perch

    432
    362
    63
    Location:
    Southampton
    Maybe it would be an idea for someone to collate these guides that have been made in to a sticky thread, how do we go about getting this done?

    ---------- Post added at 11:14 ---------- Previous post was at 11:12 ----------

    I'm almost there Rob, just waiting for the last bits to come in and I'm finishing off the website this weekend.
     
  10. Striper

    3,604
    1,754
    113
    Location:
    Guernsey
    Ask Si nicely and he might do it!

    Seem to be a lot more people into the plastic making now. Times are hard and it's a darm sight cheaper to make your own when rockie bashing that's for sure.
     
    • Like Like x 1
  11. Sea Trout

    884
    566
    93
    Location:
    Co Down Ireland
    Thanks for the step by step Alan. Even I can follow that one and that says a lot!
     
  12. Pike

    266
    311
    63
    Location:
    Dulas, ANGLESEY
    Excellent and well written step by step guide, thanks for let us all in on your mould making method. I'll give that ago later in the season.
     
  13. Sandeel

    82
    18
    0
    Location:
    Southampton
    Cheers mate,
    will search for other Jig heads, and advise
    Paul
     
  14. Pike

    271
    262
    63
    Location:
    Bangor Co Down
    excellent thread very useful, i have a few lures i want to copy before i lose them as they have been out of production for years

    IMGP0381.JPG
     
    Last edited: May 29, 2012
  15. Striper

    2,752
    2,217
    113
    Location:
    Streatham, London
    Excellent post Alan - thanks for taking the time to do it so thoroughly.
    I am looking forward to seeing the pouring. Especially after seeing the catch report bass with one of them in its gob.
     
  16. Senior Member

    2,631
    1,574
    0
    Here you go David, https://www.thelureforum.com/showthread.php?t=17010 Alan has done a series of these threads, I think they need making sticky so people can read them in order.

    I am on Alans case to either start selling his SP's ready made in packs, selling the ready made moulds ready to buy the components to make your own or to sell complete starter packs ready to make your own SP's, he is working on it.
     
  17. Chub

    614
    208
    43
    Location:
    guernsey c.i
    rob i would be intrested in a couple of the white paddle tails to see what they are like im always on the look out for diffrent paddletails
     
  18. Senior Member

    2,631
    1,574
    0
    Gavin, send Alan a PM, I am sure the more people that get on to him about wanting to buy some the more incentive he will have to make it happen.

    When I spoke to him the other night he was making a multi mould so he could make them in batches more easily, hopefully I will be getting the first lot :-D and Jon Crabb was waving money at Alan down at Redbridge the other morning so is likely to get the second, but like I said, PM him or click on his banner at the top of the page and I am sure he will make more as needed. :-D
     
  19. Chub

    614
    208
    43
    Location:
    guernsey c.i
    pm sent to him cheers rob they do look very intresting
     
  20. Perch

    432
    362
    63
    Location:
    Southampton
    They certainly look do'able, the 2 top ones have a flat top so would be quite easy to mould and to pour. The bottom one would need to be made in a 2 piece mould, but again could be done.

    I shouldn't really encourage copying of lures but if they are no longer made by the manufacturer then I don't see the harm, call it history preservation I guess.
     
    • Like Like x 1

Share This Page